There has been a successful start to the Ballinamore Build Your Own Wind Turbine Workshops.We started on Thursday 13 Nov with two participants and with Jimmy, Niall and Miriam on hand for guidance. One of the participants, Sinead, is building her own 2.4m 12volt turbine and Jonathan was learning “how to” for that windy day in the future.
On Thursday the wood for Sinead’s blades was cut up and sorted through to see which pieces would be used and how to best place them. Out of budget necessity it’s plain white pine which was laminated using wood glue. We laminated two and left the third one ’til Friday because we didn’t have quite enough clamps to secure all three blades.
All the coils were wound on Thursday and are very consistent in size and weight. Three of us wound them taking turns in winding, counting and we weighed each one as it was finished.As well as lending a hand whenever needed Niall was working on an experiment of his own. We had brought down to the workshop a couple of old (dimplex) oil radiators which had been thrown out of a neighbouring house which is being done up. They had been left under a hedge for some time when we rescued them to see if they could be used. Jimmy dried them out with the notion of using one as a local heat source which we could take turns standing beside when we got too cold in the workshop. Niall took a wire brush to the other one and gave it a good clean up, the plan is to put an immersion into it and use it as a heat dump. I am sure that Niall will write about this project himself. It was a good days work.
On Friday we started to make the moulds for the stator, marking out a sheet of 12mm ply and cutting out three x 600mm squares. We drew out the circles, added the tangents and the three mounting circles.We laminating the third blade and marked the other two for cutting out the wedge. We cut one with the electric saw and decided to do the second blade using hand tools as a good beginners session for becoming comfortable with a drawknife. After a sharpening session on the draw knives and a wee chat about using hand tools both of the participants got some good warming up using the draw knives before we finished for the day.On Saturday Sinead made good progress with the drawknife and cut out most of the wedge on the first blade. She decided to continue with the drawknife on the third blade instead of cutting off the wedge with the electric saw and by the afternoon she was feeling much more comfortable and confident with the tool. Both blades were then cleaned up by Sinead using the electric planer and finished with the hand planes, all three blades being ready for marking out for the next stage by the end of the day.
On Saturday Sinead made good progress with the drawknife and cut out most of the wedge on the first blade. She decided to continue with the drawknife on the third blade instead of cutting off the wedge with the electric saw and by the afternoon she was feeling much more comfortable and confident with the tool. Both blades were then cleaned up by Sinead using the electric planer and finished with the hand planes, all three blades being ready for marking out for the next stage by the end of the day.
The island had to be adjusted, it was a little too big for the coils to fit well. The coils were soldered and placed in the mould, avoiding the mounting points. Everyone was involved in the preparation for the next stage.
The moulds were covered in vaseline in readiness for the casting. A number of plastic bottles were cut and cleaned and left at the ready, the scales brought to the bench and two teaspoons were sacrificed for stirring the resin, hardener and talcum powder. The glass cloth was cut and extra pieces cut for the mounting points. By the end of the day the mould was cast and everyone was satisfied with another day full of activity.
Another project for the workshop was converting one of the old dimplex oil heaters to a 24v dump load ,after we stripped of the mains electrics it conviently revealed a second inch/half plug at the top , a pipe adapter was used to fit the heating element ..tests look promising and it,s probabely more easy on the eye (after a bit of paint work) and a little simpler than setting up air heater elements…. disssapting the full element power should be no problem ..you do need to turn it upside down if you leave the old 220v element in there
Hi folks, we were back Crann Og today, Saturday October 18, full crew consisted of Flor and Marion, Dinger, Sean, Niall, Jimmy and Miriam. After a lazy breakfast we set about putting things back together, having first admired the great paint job that Flor did. First was the new bearing and then fitting the stator and rotors, using the jacking screws to lower the rotor and ensuring that all the gaps are even.
Next we brought the blades back outside to put them together, using the identification marks to ensure that the blades were in the right order with each other. Dinger and Flor went around with the tape measure until we had the required distance between the tips and then it was out with battery screwdrivers, three of them, to fix the blades in place.
Back into the workshop to fix the tail to the tail frame and then after a coffee break it was time to bring everything into the field, using the tractor again to carry the alternator. It seemed easier this time round to fix the body of the turbine to the mast, using a little gentle persuasion (a 2×3) and then fix the blades, Niall measured the blade tips from the horizontal to ensure the best position.
Dinger and Jimmy raised the mast and the colours looked great even in the cloudy conditions, all went smoothly and she was spinning as soon as the brake was thrown, sounding lovely, a gentle roar when the wind picked up.
Tomorrow we are expecting winds up to 110kmph! That should test her out – the tirfor is still attached so there might be a pyjama party in the field if the winds come earlier and heavier than expected!
We’ll let ye know…
Surviving well and producing plenty of power we are going back in a week or so and will give a full report then.
2.4m Turbine build in Crann Og Gort